Covering wooden letters with fabric

Fold back the fabric margins and staple them down, again starting in the centre Covering wooden letters with fabric a straight edge and working towards the corners to keep it smooth.

Notice how the edges of the fabric sort of hang over the edge. When attaching the edging, use bias binding if you do not want to create your own [a darker shade will add even more depth to your letter.

Another neat thing about the fat quarters that works so well for the project is that they come with edges that are pinked. Coat the back of the fabric with a glue stick and wrap each section round the fabric covered edge to the wrong side.

I even bought the letters clear back in December…and they have been sitting on the shelf in my craft closet since then. Glue in place securely and as close to the edges as you can. This time I traced the letter on the other side of the fabric so I could know exactly where to place it down once I applied the glue to the letter.

One for the face of the letter, and one for the sides. I started from the top of the letter and worked down [this would help prevent any uneven pulls to the fabric, misalignment with the pattern or bulky areas over the padding]. Snip into the margin at 45 degrees, run a glue stick over reverse side to hold it tightly in place, then staple as before.

Is that even a word? Using a measuring tape, measure out where to put each nail or, in my case, sticky hook - I used the small clear ones pictured below in the wall. Embellish your letter [such as buttons or embroidery - add this to the fabric before gluing in place] Share: Cut a 4cm strip, the same depth as the letter and fix it across the corner with double-sided tape.

Fat Quarters are quarter-yard cuts of fabric cut wide hence the name fat. The letters will be very wet and will look milky, but it will dry clear. The process was like wrapping a gift.

I started with the last letter and worked my way backwards, doing one letter at a time and seeing how I liked it visually before proceeding.

I wanted owls, and I wanted those cute letters on the wall that spelled out his name. So now whatever you want to say, you can spell it in Liberty print. Covering letters with holes Step eight: Or perhaps sanding down the surface of the letters will help the fabric stick a little more smoothly.

How to Cover Wooden Letters

Finally, with the length of material cut to hide all the fixings, glue around the sides of the letter. How will I hang them in my apartment where the use of nails in the walls are not allowed?

Cut it deeper than the height of the letter, so it overlaps the back by 1cm. This will create a neat and finished look to the letter]. Preparing the cardboard backing Step one: I went the contrasting route.

Measure the distance between the center of the letters and, in my case, the distance between the varying heights. Turn the corner back at an angle, stretching it gently to get a neat edge, and staple down the point.

Apply Fabric to Letters 1. Lay out the fabric with the right side downwards and position the card letter on top, the right side up. Until next time… Advertisements. Have a little of the bias binding positioned so that it is showing from under the edging fabric, so when glued in place, it provides a beautiful edging.

Cut enough strips to go around the entire letter.

How to Make Padded Letters

I used my rotary cutter and mat. Next, I measured the depth of the letter. For some letters, there will be an underside that would be the perfect place to start and finish this attachment, hiding where the edges meet.

Ready to put the contrasting or matching trim around the edges.

How to make fabric-covered letters

Peel off the backing papers and place the letter upside down on to the fleece. Fold over the margin along the next side of the letter and carry on stapling down. Apply a next layer of glue to the back and fix the second letter piece of fabric in place, using the edge of the letter to fins the material securely.Make Your Own Fun, Fabric Covered Letters.

Cut out a piece of batting that is large enough to cover the front and sides of the killarney10mile.com a little extra to glue to the back. Now glue the excess fabric to the back of the letter, much like we did with the batting in the beginning, including trimming the excess fabric off the outer.

Brief video by the folks at Craig Bachman Imports demonstrating how to cover wooden letters with fabric. The fabric in this video is a Faux killarney10mile.com click no the image to go to youtube to see the video. Feb 06,  · DIY: Fabric Covered Wooden Letters the idea came to me: Use leftover fabric scraps to cover wooden letters so the letters match the quilt!

But I had my doubts: Will it work? How do you attach fabric to wooden letters? How will I hang them in my apartment where the use of nails in the walls are not allowed? Will it look Author: The Shipp Family How to make fabric-covered letters Wooden or MDF letter, 1cm deep Sheet of medium-weight card, the same size as the letter Cover the entire letter with fabric as above, then snip at.

How to make a DIY fabric-wrapped wooden letter decoration to hang on the wall Gather your fabric and your letter. Make sure you have enough fabric to cover your letter.

Trim the fabric leaving about inches on all sides around the letter. Make slits in the fabric at the points of angles of.

UK Craft Blog UK Food Blog Make, Bake, Create How To Make Your Own Ideas Nursey Padded Letters Monogram Fabric Craft Blog. The Things She Makes For the base of this DIY, I used a Decopatch letter – but you can either make your own, use a wooden letter or up-cycle any letter accessory.

I'm currently using these letters and covering.

Download
Covering wooden letters with fabric
Rated 4/5 based on 63 review